x

guide bearing

uploads/guide bearing.jpg

guide bearing 【機械工程】導引軸承。

【機械工程】導引軸承。 “guide“ 中文翻譯：   n. 1.引導，指導。 2.領路人，導游者，向導；指導者 ...“bearing“ 中文翻譯：   n. 1.忍耐，忍受。 2.態度，舉止，風采，姿態。 3 ...“guide bearing bracket“ 中文翻譯：   導向軸承支架; 導軸承托架; 導軸承支架“guide bearing, piston rod“ 中文翻譯：   活塞桿導向座“guide block bearing“ 中文翻譯：   導向塊軸承“guide spindle bearing“ 中文翻譯：   導軸軸承“guide vane bearing“ 中文翻譯：   導葉軸承“lower guide bearing“ 中文翻譯：   下導軸承“lower guide bearing clearance“ 中文翻譯：   下導瓦間隙“lower guide bearing journal“ 中文翻譯：   下導軸領“lower guide bearing segment“ 中文翻譯：   下導瓦“main guide bearing“ 中文翻譯：   主導軸承“pivoted-pad guide bearing“ 中文翻譯：   支樞式導軸承; 支柱式導軸承“segment guide bearing“ 中文翻譯：   分瓣導軸承“special guide bearing“ 中文翻譯：   特種導承“turbine guide bearing“ 中文翻譯：   水導軸承“turbine guide bearing clearance“ 中文翻譯：   水導軸承間隙“turbine guide bearing pad“ 中文翻譯：   水導軸瓦“u er guide bearing“ 中文翻譯：   上導軸承“upper guide bearing“ 中文翻譯：   上導軸承“upper guide bearing clearance“ 中文翻譯：   上導軸承間隙“lower guide bearing jacking bolt“ 中文翻譯：   下導瓦調整絲頂“lower guide bearing metal temperature“ 中文翻譯：   下導瓦溫“thrust and lower guide bearing skids“ 中文翻譯：   推導油外循環裝置“turbine guide bearing oil pot“ 中文翻譯：   水導油槽

guide board

Second , adopting the linearity of oil film of the guide bearings , the transient response of the shafts is computed and analysis by integrating with willson method . because of the uncertain position of the shafts in the guide bearing , the model and solution method of nonlinear transient response of the shafts is discussed 然后結合willson數值積分法，采用線性化油膜力，對機組軸系的線性瞬態響應進行了計算分析，根據機組軸系在瞬態響應中運動的不確定性，給出了由導軸承油膜力非線性所引起的主軸系統的非線性瞬態響應的建模及求解方法。

Thirdly , the correlative coefficient is computed between the pressure fluctuation signal of draft tube and the displacement signal of upper guide bearing , the thrust bearing and the head cover , with this the conclusions on the shafts response due to pressure surge in 并與模型尾水管壓力脈動試驗結果進行對比?結合流動仿真試驗以及動力特性計算結果,全面分析?評定機組的實際運行狀況,劃定運行區域,為電站合理調度

First , the system boundary of machines affecting the shafts , such as the guide bearings , seal , electrical and hydraulic forces , the water in the runner etc , is analyzed . and the mathematic model of the system boundary of the machine is built 本文首先分析了對機組主軸系統影響較大的系統邊界條件，如導軸承、水封、電磁拉力、轉輪處的水體等，并分別建立了它們的數學模型。

Production and application of thrust bearing , and guide bearing made of filled ptfe in submarine motor pump are introduced 介紹了潛水泵中止推軸承與導向軸承用填充聚四氟乙烯材料進行的生產和應用。